Notes

Deck Footing - Henrico County, Virginia

<div itemscope itemtype="http://schema.org/ImageObject">
<img class="featurable" style="max-height:300px;max-width:400px;" itemprop="image" src="https://www.diychatroom.com/attachments/img_20160328_074723-jpg.260449/" alt="How to Perform an Inspection for Deck Safety - WoodIt's Real- Wood It's Real."><span style="display:none" itemprop="caption">Deck Inspection: Checklist for Framing, Footings and More - Decks.com</span>
</div>
<br>
<br>
<h1 style="clear:both" id="content-section-0">Deck Inspection Checklist - Sherwood Inspection Services, LLC Fundamentals Explained<br></h1>
<br>
<img width="306" src="http://thebirminghamhandyman.com/press/wp-content/uploads/2011/04/IMG00139.jpg">
<br>
<p class="p__0">Lag screws must also be a minimum of -inch in size and have washers. Expansion and adhesive anchors should likewise have washers. Deck journals should be of a minimum of 2'x 8' pressure-treated wood. Ledger Board and Band Joist Contact: The image above depicts washers being utilized as spacers in between the ledger board and band joist, which is incorrect.</p>
<br>
<p class="p__1">In other cases, there is insulation in between the two boards. Even even worse is when the siding or exterior finish system was not eliminated prior to the setup of the ledger board. Circumstances like this, where the journal board and band joist are not in direct contact, substantially lower the strength of the ledger connection to the structure and are not suggested by Inter, NACHI, unless the two members are sandwiching structural sheathing.</p>
<br>
<p class="p__2">All through-bolts need to have washers at the bolt head and nut. The image above depicts a hold-down tension device. The 2007 IRC Supplement requires hold-down tension gadgets at no less than two areas per deck. Codes in some locations outright forbid attaching a journal board to an open-web floor truss.</p>
<br>
<h1 style="clear:both" id="content-section-1">See This Report on Deck Restoration: DIY Inspection Guide - Eby Exteriors<br></h1>
<br>
<p class="p__3">Caulking rather than flashing is utilized. The image above illustrates a ledger board attached to hollow masonry. When the ledger is connected to a hollow masonry wall, the cell must be grouted. The image above illustrates a ledger board incorrectly supported brick veneer. Ledger boards should not be supported by stone or brick veneer.</p>
<br>
<p class="p__4">Stucco and EIFS need to be cut back so that journal boards can be attached straight to band joists; nevertheless, cut-back stucco and EIFS are difficult to flash and weather-proof. The image above portrays both over and under ledger board flashing. The ledger board ought to constantly be flashed even when the home or structure has a protective roofing system overhang.</p>
<br>
<div itemscope itemtype="http://schema.org/ImageObject">
<img class="featurable" style="max-height:300px;max-width:400px;" itemprop="image" src="https://www.milesbradley.com/wp-content/uploads/2020/01/deck-inspection.jpg" alt="Deck Safety - Is the Deck You Are Standing On As Secure As You Think?"><span style="display:none" itemprop="caption">NYC launches free no-penalty inspections of home, small business structures - silive.com</span>
</div>
<br>
<br>
<p class="p__5">Contact with pressure-treated wood or galvinized fasteners can cause quick deterioration of aluminum. Full Article illustrates a deck journal connected to an overhang. Decks must not be connected to overhangs. The image above depicts appropriate framing around chimneys or bay windows that are up to 6 feet broad.</p>
<br>

Here's my website: https://jcdecks.com